140CPU67260控制器模SCHNEIDER
入输出模块PI输入输出模块ABB调节Control strategies and system configurations created on
earlier DeltaV systems can be used with this controller.
The SQ controller provides all the features and functions
of the M-series controllers including support for CHARM
based Electronic Marshalling.

   传感器的灵敏度为280mV/cm/S，则它的输出电压(标准值)即为280mV。

 当被校准的传感器为水平传感器时，校准仪应水平放置。

   当被校准的传感器为垂直传感器时，校准仪应垂直放置。

TD-2-50TD-2型热膨胀传感器

TD-2型热膨胀传感器主要用于测量汽轮机汽缸膨胀位移量，与热膨胀监控仪相配合即可完成热膨胀位移量的远传指示、报警、恒流输出等功能。就地指示视野大，远传指示为数字显示，清晰直观。采用中频差动变压器式位移传感器作为传感元件，是一种高可靠的 LVDT 位移传感器，抗力强，线性好，结构简单，不易损坏，能连续使用。

 

振动速度传感器是利用磁电感应原理把振动信号转换成电信号。它主要由磁路系统、线圈组件、弹簧阻尼等部分组成。在传感器壳体中刚性地固定有两个线圈组件，磁钢用弹簧悬挂于壳体。当传感器在工作频率范围内工作时，线圈与磁钢产生相对运动，线圈切割磁力线，产生感应电动势（感应电压），该电压正比于机壳的振动速度。温度传感器的温度测量是利用铂电阻随温度线性变化的性质来测温的。


技术指标：
1. 量程： 0～50mm （量程由用户自定） 
2. 准确度：± 1% （满量程） 
3. 环境温度： -20 ℃ ～+100 ℃ 
4. 相对湿度：≤ 80% 

技术参数

1．振动传感器 
灵 敏 度：30mV/mm/s 
加 速 度：8g 
测量范围：2mm 
频率响应：10~300Hz 
2．温度传感器：PT100 
测量范围：0～400℃ 
3．环境温度：-10～100℃ 
4．测量方法：垂直、水平、轴向 
5．固定螺孔：在Φ85的圆周上均匀分布用4个M8螺钉固定 
6．外形尺寸：Φ70mm×180mm 
7．插入深度：83mm

TD-2-50TD-2型热膨胀传感器TD-2-35 Thermal expansion transmitter

It is mainly used to measure the expansion displacement of steam turbine cylinder, and it can complete remote indication, alarm, constant current output and other functions of thermal expansion displacement with XCW-R thermal expansion monitor. The field of vision of local indication is large, and the remote indication is digital display, which is clear and intuitive. The medium frequency differential transformer displacement sensor is used as the sensing element. It is a highly reliable LVDT displacement sensor with strong resistance, good linearity, simple structure, and is not easy to be damaged. It can be used continuously.



Technical indicators:



1. Range: 0 ～ 50mm (the range is determined by the user)

2. Accuracy: ± 1% (full scale)

3. Ambient temperature: - 20 ℃~+100 ℃

4. Relative humidity: ≤ 80%



Sensor structure diagram:





model



Linear range



Sending head extended

Length (L) mm



TD-2-25



twenty-five



ninety



TD-2-35



thirty-five



ninety-five



TD-2-50



fifty



one hundred and seven





Ordering Guide:



Model selection code: TD-2 - A □□

Model Selection Description:

Range A □□:

01 —— 0 ～ 25mm ；

02 —— 0 ～ 35 mm ；

03 —— 0 ～ 50 mm ；



If you have special requirements, please consult with our company.



TD-2-35 Thermal expansion transmitter



Vibration, vibration intensity, shaft vibration, axial displacement, intelligent speed, thermal expansion, differential expansion, hydraulic servo motor, oil level of oil tank, turbine monitor, monitor and protector;



Eddy current, vibration speed, Hall speed, magnetic resistance, thermal expansion, hydraulic motor, oil tank level sensor;



Axial displacement, vibration, integrated vibration, speed, thermal expansion, hydraulic servo motor, oil level transmitter of oil tank.









TD-2 Thermal Expansion Travel Transmitter

TD-2 type thermal expansion travel transmitter is equipped with various TD-2 type linear differential transformer sensors. The built-in excitation source and differential measurement circuit convert the thermal expansion on both sides of the casing into 4~20mA current output. The difference between the two represents the deformation of the casing. This deformation will cause huge stress between the casing and the foundation, resulting in misalignment. If the casing sliding pin system is jammed, serious consequences will be caused.



Technical indicators:



1. External power supply: 24V DC

2. Input signal: receive the signal of a LVDT linear differential transformer; Input impedance:>90K Ω

3. Range: 0 ～ 50 mm

4. Accuracy: ± 1% of full scale

5. Current output: 4 ～ 20 mA active; Output load: ≤ 500 Ω

6. Temperature range: - 25 ℃~+65 ℃ during operation; - 40 ℃~+85 ℃ during storage

7. Relative humidity: 90%, non solidification

8. Physical index: overall dimension 80 × sixty × 50mm ; Mounting screw hole size 50 × 50mm



Order guide



Thermal expansion travel transmitter must be equipped with TD-2 thermal expansion sensor forming system



Model selection code: TD-2 - A □

Model Selection Description:

Range A □: 1 -- 0 ～ 25 mm; 2＊——0～35 mm； 3——0～50 mmBT-50膨胀传感器

　　概述
　　BT-50**膨胀传感器是为汽轮机行业测量汽轮机组**膨胀位移所设计的传感器，它采用中频位移传感器（LVDT）作为传感元件，LVDT有一个探杆与机器相连。当机壳膨胀时，探杆在LVDT内移动，引用LVDT信号发生变化。信号经过解调后输出到监测器上，用于显示和报警。

　　BT-50**膨胀传感器由15-24VDC供电，输出直流电压信号，具有远传线性好，抗干扰性能力强，不易损坏，可靠性好，能连续使用的特点。
　　
　　用途
　　适用于汽轮机汽缸膨胀测量及保护。

　　技术参数
　　线性量程：0~50mm.
　　非线性度：不-20大于0.5%FS.
　　工作温度：-20℃~75℃
　　供电电源：15VDC~24VDC
　　输出信号：±5.8~±10V.
　　环境湿度：不大于95%（非冷凝）。
　　环境振动：不大于2.3g.
　　工作方式：连续
　　执行标准：参照JJG　644-2003　

BT-50膨胀传感器

TD-2 系列膨胀传感器是为汽轮机行业测量汽轮机组膨胀

位移所设计的传感器，它有就地和远传两种指示。就地指示视野大，它

采用中频位移传感器作为传感元件；远传指示线性好，抗干扰性强，结

构简单，不易损坏，可靠性好，能连续使用，输出为恒流。已被国

内大中型汽轮机制造厂选用，其它精密测量行程的位移场合也可采用。

产品出厂时可选配变送器或二次数字仪表，订货时说明。