330186-02产品描述GE RST模拟I/O板DS200TCQAG1包含六个34针连接器、两个40针连接器和六个跳线。该板还具有6个LED。LED排列成两行,每行有三个LED。当板安装在驱动器中时,它安装在其他板之间,从板柜的玻璃正面可以看到GE RST模拟I/O板DS200TCQAG1的侧面。
LED的排列使操作员可以在驱动器运行时看到它们。LED指示板的6个功能的运行状况,并且在活动发生时闪烁。要了解每个LED的用途,您可以阅读出厂时随原始电路板提供的安装说明中提供的有关LED的信息。驱动器操作员可以一目了然地确定电路板的健康状况和正在进行的处理。
JA、JB、JD、JE、JG和3PL是分配给34针连接器的ID。ID打印在每个连接器旁边的电路板表面上。当您计划更换电路板时,请在驱动器中检查有缺陷的电路板,并在带状电缆上标记它所连接的连接器的ID。这将加快新电路板的安装速度,因为您将立即知道34针带状电缆的连接位置。握住带状电缆连接到电路板的连接器以将其分离。
有关DS215TCQAG1BZZ01A的常见问题
DS215TCQAG1BZZ01A读取哪些类型的输入?
DS215TCQAG1BZZ01A读取LVDT输入。VDC1和VDC2的个冗余传感器输入也通过专用带状电缆传输到<R>控制处理器中的DS215TCQAG1BZZ01A。
DS215TCQAG1BZZ01A软件中包含哪些调节器?
数字控制调节器是Mark V中每个控制处理器DS215TCQAG1BZZ01A上I/O配置软件的一部分。
当Mark V发生故障自杀时,DS215TCQAG1BZZ01A会发生什么?
当Mark V上启用电流故障自杀时,DS215TCQAG1BZZ01A上的继电器将断电,DS215TCPQAG1BZZ11A上的一对常闭触点将使输出端子短路。
在哪里可以找到DS215TCQAG1BZZ01A的手册?
我们可以为您提供DS215TCQAG1BZZ01A的手册。与DS215TCQAG1BZZ01A一起使用的手册是Speedtronic Mark V涡轮机控制应用手册,手册GEH-6195,本手册涵盖Mark V Speedtroni控制器的应用信息,手册提供了DS215TCQA G1BZZ01的详细信息。产品描述
GE驱动器控制板DS200SDCCG1ACA是驱动器的主控制器。GE驱动控制板DS200SDCCG1ACA配备有3个微处理器和RAM,可由多个微处理器同时访问。对于可选功能,您可以向GE驱动器控制板DS200SDCCG1ACA添加辅助板。可选卡连接到板上,连接器可用于将电缆从可选卡连接至板。
这些卡能够连接到局域网(LAN),并处理多桥信号,或处理从板发送或由板接收的信号。如果安装了可选卡并更换了GE驱动器控制板DS200SDCCG1ACA,则必须执行一些其他步骤来执行更换。首先,从驱动器中取出有缺陷的电路板后,将电路板放在保护袋上,然后将保护袋压平,放在水平表面上。接下来,从板上卸下可选卡并断开所有电缆。在安装替换板之前,将板放在保护袋上,安装可选卡并连接电缆。然后,继续安装更换板。
GE驱动控制板DS200SDCCG1ACA具有十个LED灯,它们一起工作以提供板的状态。LED位于一行中,当电路板无故障运行时,两个LED同时按顺序闪烁,以指示电路板运行正常。
有关DS200SDCCG1ACA的常见问题解答
DS200SDCCG1ACA有多少个卡连接?
DS200SDCCG1ACA有8个卡连接器。DS200SDCCG1ACA通过这些连接器与控制器的其他板和外部信号连接。DS200SDCCG1ACA的连接器包括:1PL、2PL、3PL、6PL、7PL、8PL、9PL和11PL。要查看DS200SDCCG1ACA上连接器的位置,请参阅DS200SDCGG1ACA手册中的图3-手册GEI-100029。
DS200SDCCG1ACA上可以安装哪些板?
DS200SDCCG1ACA具有其他辅助板和模块的安装规定。可安装在DS200SDCCG1ACA上的板有:DS215SLCC或531X306LCC LAN通信卡、531X309PC信号处理器卡和DS200SPCB多桥信号处理器卡。
DS200SDCCG1ACA使用哪本手册?
DS200SDCCG1ACA使用的手册是GE Motors and Industrial Systems Drive Control Card manual-manual GEI-100029。本手册提供DS200SDCCG1ACA的功能说明,手册提供了DS200SDCG1ACA的应用数据,手册提供DS200 SDCCG1AAC的更新/保修更换信息。尽管本手册未涵盖所有DS200SDCCG1ACA操作或故障排除,但本手册有助于向您介绍DS200SDCG1ACA。
DS200SDCCG1ACA用于哪些应用程序?
DS200SDCCG1ACA用于AC2000、DC2000和EX2000驱动器应用Product Description
The GE RST Analog I/O Board DS200TCQAG1 contains six 34-pin connectors, two 40-pin connectors, and six jumpers. The board also has 6 LEDs. The LEDs are arranged in two rows with three LEDs in each row. When the board is installed in the drive, it is installed between other boards and the side of the GE RST Analog I/O Board DS200TCQAG1 is visible from the glass front of the board cabinet.
The LEDs are arranged so the operator can see them while the drive is in operation. The LEDs indicate the health of 6 functions of the board and they flash when activity takes place. To understand the purpose of each LED, you can read the information about the LEDs provided in the installation instructions that are supplied with the original board from the factory. The drive operator can at a glance ascertain the health of the board and the processing taking place.
JA, JB, JD, JE, JG, and 3PL are the IDs assigned the 34-pin connectors. The IDs are printed on the surface of the board next to each connector. When you plan to replace the board, inspect the defective board while it remains in the drive and mark on the ribbon cables what the ID is of the connector it is attached to. It will speed up the installation of the new board because you’ll know immediately where to connect the 34-pin ribbon cables. Hold the ribbon cable by the connector where it attaches to the board to detach it.
Frequently Asked Questions about DS215TCQAG1BZZ01A
What types of inputs does DS215TCQAG1BZZ01A read?
DS215TCQAG1BZZ01A reads LVDT inputs. The first of the the redundant transducer inputs for VDC1 and VDC2 are also communicated to DS215TCQAG1BZZ01A in the < R > control processor by a dedicated ribbon cable.
What regulators are part of DS215TCQAG1BZZ01A's software?
Digital control regulators are part of the I/O configuration software on DS215TCQAG1BZZ01A in each control processor in Mark V.
What happens to DS215TCQAG1BZZ01A when a fault suicide occurs on a Mark V?
When a current fault suicide is enabled on a Mark V, a relay on DS215TCQAG1BZZ01A will be de-energized and a pair of normally-closed contacts on DS215TCQAG1BZZ01A will short the output's terminals together.
Where can I find the manual for DS215TCQAG1BZZ01A?
We can provide you with the manual for DS215TCQAG1BZZ01A. The manual to use with DS215TCQAG1BZZ01A is the Speedtronic Mark V Turbine Control Application Manual, Manual GEH-6195, and this manual covers application information for Mark V Speedtronic controllers and the manual provides specifics about DS215TCQAG1BZZ01A.产品描述
GE励磁板DS200UDSAG1ADE具有一个1 80196微处理器和几个可擦除可编程只读存储器(EPROM)模块。GE励磁板DS200UDSAG1ADE还配有21个4字符显示屏和32个LED。由于电路板装有微处理器,因此电路板和驱动器必须在通风良好的环境中工作。环境也必须清洁,无灰尘、污垢和油。要创建一个干净凉爽的环境,您选择安装驱动器的位置是个也是重要的考虑因素。
要选择位置,请考虑其他驱动器和设备距离足够远,不会导致温度过高。驱动器还必须通风良好,在某些情况下需要风扇来冷却现场。如果使用风扇,请确保风扇处于良好状态,并适合空间大小。冷空气通过驱动器底部的通风口进入驱动器。空气通过驱动装置,从部件中带走热量。在驱动器顶部,热空气离开驱动器。
当您计划安装时,请注意空间周围的墙壁是否很热。相邻房间的驱动器和其他设备可能会加热墙壁。您可以考虑选择其他空间来安装驱动器或在其他设备未使用时使用驱动器。这样,墙壁会更凉爽,不会产生过多的热量。
Product Description
The GE DC Power Connect Board DS200PCCAG10ACB serves as an interface between the drive and the SCR power bridge. Once you install the replacement DS200PCCAG10ACB board you might have reason to download the configuration file of the drive to a laptop for review. You can edit the configuration file and change parameters to update the operation of the drive with the replacement board installed.
To download the parameters file, first make sure you have a serial cable that has the matching ports you need to connect the drive to the laptop. Also, make sure the serial port on the laptop is configured properly to communicate with the drive. Use the commands on the control panel to initiate the download and when complete a message displays on the display panel that the download is complete.
You can use the laptop to check the operation of the replacement board by viewing the diagnostic file. You can also access the editing software on the laptop to alter the board's parameters. When you have completed the updates, upload the file back to the drive. Use the control panel to start the download procedure and when the operation is complete, a will be message displayed.
To replace the DS200PCCAG10ACB board, you must disconnect all power to the drive. To do that, access the 3-phase power supplies that provide current to the drive. Then, remove the fuses from the power supplies. Next, you can open the bay that contains the boards and remove the wires and connectors.
Frequently Asked Questions about DS200PCCAG10ACB
What does DS200PCCAG10ACB do for lower horsepower controllers?
For low-to-medium horsepower controllers, DS200PCCAG10ACB includes snubber circuits to control spikes across the AC lines, DC bus, and gate drivesr. For higher horsepower controllers, some or all of the snubber circuits are omitted from the DS200PCCAG10ACB board.
How many jumpers does DS200PCCAG10ACB have?
DS200PCCAG10ACB has four wire jumpers. DS200PCCAG10ACB's jumpers are JP1, JP2, WP3, and WP4. The jumpers on DS200PCCAG10ACB select system voltage and determine snubber capacitor connectors.
What type of snubbers does DS200PCCAG10ACB connect to?
Because DS200PCCAG10ACB is a G10 board group PCCA, DS200PCCAG10ACB only connects to DC snubbers.
Where can I find the manual for DS200PCCAG10ACB?
We can send you the manual for DS200PCCAG10ACB. We have the manual to DS200PCCAG10ACB on file and will send the manual upon request. The manual for DS200PCCAG10ACB is Manual GEI-100161 - The GE Industrial Control Systems PCCA Power Connect Card Manual.产品描述
GE DC电源连接板DS200PCCAG10ACB用作驱动器和SCR电源桥之间的接口。安装替换DS200PCCAG10ACB板后,您可能有理由将驱动器的配置文件下载到笔记本电脑以供查看。您可以编辑配置文件并更改参数,以更新安装了更换板的驱动器的操作。
要下载参数文件,首先确保您有一条串行电缆,该电缆具有将驱动器连接到笔记本电脑所需的匹配端口。此外,确保笔记本电脑上的串行端口配置正确,可以与驱动器通信。使用控制面板上的命令启动下载,完成后,显示面板上显示下载完成的消息。
您可以使用笔记本电脑通过查看诊断文件来检查更换板的操作。您还可以访问笔记本电脑上的编辑软件来更改电路板的参数。完成更新后,将文件上载回驱动器。使用控制面板启动下载程序,操作完成后,将显示一条消息。
要更换DS200PCCAG10ACB板,必须断开驱动器的所有电源。为此,请访问为驱动器提供电流的三相电源。然后,从电源上拆下保险丝。接下来,您可以打开包含电路板的托架并卸下电线和连接器。
有关DS200PCCAG10ACB的常见问题解答
DS200PCCAG10ACB对低功率控制器有什么作用?
对于中低功率控制器,DS200PCCAG10ACB包括缓冲电路,用于控制交流线路、直流母线和栅极驱动器上的尖峰。对于更高功率的控制器,DS200PCCAG10ACB板上省略了一些或所有缓冲电路。
DS200PCCAG10ACB有多少跳线?
DS200PCCAG10ACB有四个跳线。DS200PCCAG10ACB的跳线为JP1、JP2、WP3和WP4。DS200PCCAG10ACB上的跳线选择系统电压并确定缓冲电容器连接器。
DS200PCCAG10ACB连接到哪种类型的缓冲器?
由于DS200PCCAG10ACB是G10板组PCCA,DS200PCCAG10ACB仅连接到DC缓冲器。
在哪里可以找到DS200PCCAG10ACB的手册?
我们可以向您发送DS200PCCAG10ACB手册。我们已将手册存档到DS200PCCAG10ACB,并将根据要求发送手册。DS200PCCAG10ACB的手册是手册GEI-100161-GE工业控制系统PCCA电源连接卡手册。Industrial Ethernet Switch IS420ESWBH3A is part of the Mark VIe Safety Control System designed by General Electric. This switch does not have any fiber ports but has sixteen copper ports, the copper ports are 10/100Base-TX RJ45 ports. The primary operation of the switch is to perform as a level one Ethernet switch which will center on the capability to buffer multicast and broadcast packets. There should be enough space to allow for the buffer of one packet per port; if multiple incoming streams are being sent to the switch, it can only accept one incoming stream out of the multiple streams and will buffer the remaining streams for later transmission.