GE 点火电路控制板 DS200FCRLG1AFC 具有 27 个卡口式连接器。它还配有 27 个跳线、1 个 34 针连接器和 1 个 9 针连接器。GE 点火电路控制板 DS200FCRLG1AFC 上的跳线配置从连接器传输的点火信号。因此，它们很重要，您在更换电路板时必须考虑它们。每个跳线可以覆盖板上 3 个跳线中的 2 个。跳线可以覆盖引脚 1 和 2 或引脚 2 和 3。根据覆盖的引脚，电路板的行为会发生变化。

　　当电路板出厂时，包装中包含一份安装指南，其中包含每个跳线的说明。它描述了如果引脚 1 和 2 被覆盖或者引脚 2 和 3 被覆盖时配置如何变化。跳线在电路板上用两个字母 ID 标识，JP 后跟一个数字。跳线 ID 的一些示例是 JP1、JP4 和 JP9。安装人员将与工程师和操作员协商，以确定应如何配置驱动器以好地满足现场需求。配置完成后，驱动器将在正常处理过程中按需运行。

　　要更换驱动器，一步是检查旧板上的跳线设置并移动替换板上的跳线以匹配。一些跳线将保留在默认位置，即跳线出厂时的位置。它们通常是常见的设置。该板只是复杂驱动器中的一个组件。驱动器中的许多组件(包括嵌入式电气组件)都会产生热量。为了使电路板有效且无错误地运行，驱动器必须安装在始终凉爽或室温的位置。选择安装位置时，请为驱动器选择一个空间，驱动器与其他设备之间的距离至少为 18 英寸。这将为所有设备留出空间来散发它们将产生的热量。请记住，驱动器必须有持续的冷空气供应才能在其中循环，并使组件保持在热阈值以下，以避免自动出现错误消息或操作中断。如果空间中有发热设备，您可能需要安装风扇来帮助冷却驱动器。确保安装了足够的风扇并且它们处于良好状态且可靠。如果组件变得太热并且温度上升到阈值以上，则会出现过热情况，并且驱动器将在没有人为干预的情况下关闭。过热情况记录在错误日志中，The GE ignition circuit control board DS200FCRLG1AFC has 27 bayonet connectors. It also comes with 27 jumpers, 1 34 pin connector, and 1 9 pin connector. The jumper configuration on the GE ignition circuit control board DS200FCRLG1AFC transmits the ignition signal from the connector. Therefore, they are important and you must consider them when replacing the circuit board. Each jumper can cover 2 out of 3 jumpers on the board. Jumpers can cover pins 1 and 2 or pins 2 and 3. The behavior of the circuit board will change depending on the pins covered.



When the circuit board leaves the factory, the packaging includes an installation guide that includes instructions for each jumper. It describes how the configuration changes if pins 1 and 2 are covered or pins 2 and 3 are covered. Jumpers are identified with two letter IDs on the circuit board, followed by a number. Some examples of jumper IDs are JP1, JP4, and JP9. The installation personnel will consult with engineers and operators to determine how to configure the drive to best meet on-site requirements. After configuration is completed, the drive will run as needed during normal processing.



The first step to replacing a drive is to check the jumper settings on the old board and move the jumper on the replacement board to match. Some jumpers will remain in their default position, which is the position of the jumpers at the factory. They are usually the most common settings. This board is just a component in a complex drive. Many components in the drive, including embedded electrical components, generate heat. In order for the circuit board to operate effectively and without errors, the driver must be installed in a position that is always cool or at room temperature. When selecting the installation location, please select a space for the drive, with a minimum distance of 18 inches between the drive and other devices. This will leave space for all devices to dissipate the heat they will generate. Please remember that the drive must have a continuous supply of cold air to circulate within it and keep the components below the thermal threshold to avoid automatic error messages or operational interruptions. If there are heating devices in the space, you may need to install a fan to help cool the drive. Ensure that sufficient fans are installed and that they are in good condition and reliable. If the component becomes too hot and the temperature rises above the threshold, overheating will occur, and the drive will shut down without human intervention. The overheating situation is recorded in the error log